- 1 Should plywood go under metal roof?
- 2 What underlayment should be used under metal roofing?
- 3 Do you need OSB under metal roof?
- 4 What goes under a metal roof?
- 5 Can you put metal roofing directly on rafters?
- 6 How do you stop condensation on a metal roof?
- 7 Which roof underlayment is the best?
- 8 Can you leave shingles under metal roof?
- 9 Can you put metal roof over shingles without furring strips?
- 10 Should a metal roof be installed over battens?
- 11 Can you walk on a metal roof with purlins?
- 12 How far apart are purlins put for a tin roof be?
Should plywood go under metal roof?
For many applications, a layer of plywood underneath your metal roofing is an unnecessary expense. Boards measuring 1 inches by 4 inches or 2 inches by 4 inches are commonly used for purlins, though never use treated lumber because it will corrode the steel roof and fasteners.
What underlayment should be used under metal roofing?
The traditional and most common material used for roof underlayment on a steep-slope metal roof is non-perforated, asphalt-impregnated felt underlayment. There are several types of felt underlayment including both organic reinforced and inorganic reinforced.
Do you need OSB under metal roof?
The simple answer is yes, your roof does need an underlayment. Traditionally built homes will need an underlayment. If your home is built with joists, insulation between those joists, and sheathing, then an underlayment is needed before you put on a metal roof.
What goes under a metal roof?
The three main types of underlayment for metal roofs include felt, synthetic sheet, and self-adhering membrane. Without an underlayment, the roof and rest of the home are exposed to the elements, which include not only wind and moisture but also chemicals and resin.
Can you put metal roofing directly on rafters?
Metal roofing can be installed directly on open rafters. The vapor barrier built into such insulation helps to minimize the amount of condensation that drips down from the roof, and the insulation itself can help to keep the interior of the building at a comfortable temperature.
How do you stop condensation on a metal roof?
Traditionally, condensation is managed by insulating the metal roof so that the panel temperature never reaches the dew point. This is often accomplished using vinyl-backed fiberglass insulation to prevent humid air from coming into contact with the cooler metal roof (which may be at or below the dew point).
Which roof underlayment is the best?
Tyvek is a good choice as an underlayment to roofing products other than asphalt shingles—things like cedar shingles and metal roofing. It’s also a fully weatherproof underlayment, which is a huge advantage in areas that see a lot of extreme weather events.
Can you leave shingles under metal roof?
In simplest terms: Yes, you can install a metal roof over shingles. Building officials in some areas will only allow a re-roof over one layer of shingles, while officials in other places may allow you to place the roof over two layers of shingles.
Can you put metal roof over shingles without furring strips?
You should not attach metal to asphalt shingles without furring out the roof first. Install radiant barrier, install 1″X4″ battens, install metal.
Should a metal roof be installed over battens?
By design, some metal roofs MUST be installed over battens, some MUST NEVER be installed over battens, and some can be installed over battens OR solid decking. So, whichever way you go, it’s important to choose the right product and install it per manufacturer specifications.
Can you walk on a metal roof with purlins?
All metal roofing systems, especially steel roofing, can be walked on. Proper fall protection is always important when walking on any roof – never walk on a wet roof or one that has dew on it. Never walk on metal roofing panels before they are properly fastened down.
How far apart are purlins put for a tin roof be?
The purlin are ultimately used to fasten the roof steel providing a diaphragm effect, along with the siding, when properly engineered and installed. Spacing is typically 24″ on center in low snow loads and is reduced based upon truss span and snow load.