Readers ask: Which Plywood Is Best For Roofing?

What thickness plywood is used for roofing?

Most Common Thickness The most common rafter spacing is 24 inches, and 5/8-inch plywood is recommended for that. It will support roof loads for most situations and is the standard for most roof applications. Roofs with very heavy loads may require 3/4-inch thickness.

What grade of plywood is used for roof sheathing?

1/2 or 3/4-inch Plywood for Roof Sheathing? – Traditionally, 1/2-in CDX plywood was common choice with 24-in rafter spacing. However, heavier roof loads may require the use of 3/4-in CDX plywood for roof sheathing. Roofs with less pitch often carry heavier loads, including snow and ice accumulations in the winter.

What type of wood should be used for roofing?

Oriented strand board (OSB) – OSB is the most common type of material used for roof decking. It’s durable and readily available, and has relatively low costs. OSB is made of interwoven strands of wood bonded with adhesive.

You might be interested:  FAQ: 16 Guage Steel Comparable To What Plywood?

What is the best thickness for roof sheathing?

The recommended thickness for roof sheathing is ⅝” thick. Sheathing with a thickness of less than that is much more likely to result in bowing between framing which could potentially compromise your exterior roof material.

What is better for roofing OSB or plywood?

OSB takes longer than plywood to get saturated, but also takes much longer to dry out. When used as roof sheathing, this tendency to hold moisture means it will degrade faster than plywood when exposed to chronic leaks.

Is CDX plywood good for roofing?

Only use CDX plywood for the interior of a house, where water damage is far less likely. Do not use CDX for roofing, sheds, or other places that are exposed to moisture consistently. The sole exception to this is pressure treated CDX, which can survive for decades without even a protective coating.

Do I need plywood on my roof?

Aside from shingles and underlayment, plywood decking is one of the most important components in your roof. The plywood decking is integral in keeping your home free of unwanted water and mold. If the plywood has gotten wet, it can have a disastrous effect on the rest of your roof, especially the shingles.

Is 7/16 OSB OK for roofing?

or a non-laminated panel, such as this OSB. Either one is acceptable. The typical thickness of roof sheathing is about 7/16-inch, which is just under 1/2-inch. If you find 3/8-inch plywood installed as roof sheathing, it’s a good idea to make your client aware of its presence.

You might be interested:  Question: How To Cut Plywood Panels To 1/64?

Can you use plywood for a roof?

You can use any cheap plywood or even particle board as a short term sheathing on a shed roof, but cover it with a layer of rolled roofing. As Sharptooth said, it will delaminate in no time if not covered. Roll Roofing is inexpensive and easy to install.

Do I need treated timber for roof?

5 Answers from MyBuilder Roofers Hi, no you do not have to treat for something that doesn’t exist. Breathable felt and correct installation of the roof insulation will allow the timbers to stay dry and free from future rot.

How much is a sheet of plywood for roofing?

Your price could vary depending on how much the roofing company charges for labor, but generally, you can expect to spend between $70 to $100 for each sheet of plywood. A 4 x 8 sheet of plywood covers about 32 square feet of roof area—and the average roof measures about 3,000 square feet.

Can you put 2 layers of plywood on a roof?

The new plywood will have to be nailed to the rafters or roof trusses. That increase in weight should not be a problem with the single layer of asphalt shingles you will be installing, because it is normally safe to assume the roof structure is built to support the weight of two layers of asphalt shingle roofing.

Can I use screws for roof sheathing?

Screws can be used for even greater withdrawal strength, but should be sized by the building designer. Staples are not recommended for roof sheathing attachment in high-wind areas. It is extremely important to have proper fastener spacing on all panels.

Leave a Reply

Your email address will not be published. Required fields are marked *