- 1 Which plywood is best for roofing?
- 2 Is 7/16 OSB OK for roofing?
- 3 What grade of plywood is used for roof sheathing?
- 4 What is the best thickness for roof sheathing?
- 5 What is better for roofing OSB or plywood?
- 6 How much does a sheet of roofing plywood cost?
- 7 Which side of OSB goes down?
- 8 Can you put 2 layers of plywood on a roof?
- 9 Do I need plywood on my roof?
- 10 Can you use CDX plywood on a roof?
- 11 Can I use screws for roof sheathing?
Which plywood is best for roofing?
CDX is the grade of plywood most commonly used for roofing (CDX plywood means it is Construction Grade for exterior purposes).
Is 7/16 OSB OK for roofing?
or a non-laminated panel, such as this OSB. Either one is acceptable. The typical thickness of roof sheathing is about 7/16-inch, which is just under 1/2-inch. If you find 3/8-inch plywood installed as roof sheathing, it’s a good idea to make your client aware of its presence.
What grade of plywood is used for roof sheathing?
1/2 or 3/4-inch Plywood for Roof Sheathing? – Traditionally, 1/2-in CDX plywood was common choice with 24-in rafter spacing. However, heavier roof loads may require the use of 3/4-in CDX plywood for roof sheathing. Roofs with less pitch often carry heavier loads, including snow and ice accumulations in the winter.
What is the best thickness for roof sheathing?
The recommended thickness for roof sheathing is ⅝” thick. Sheathing with a thickness of less than that is much more likely to result in bowing between framing which could potentially compromise your exterior roof material.
What is better for roofing OSB or plywood?
OSB takes longer than plywood to get saturated, but also takes much longer to dry out. When used as roof sheathing, this tendency to hold moisture means it will degrade faster than plywood when exposed to chronic leaks.
How much does a sheet of roofing plywood cost?
Your price could vary depending on how much the roofing company charges for labor, but generally, you can expect to spend between $70 to $100 for each sheet of plywood. A 4 x 8 sheet of plywood covers about 32 square feet of roof area—and the average roof measures about 3,000 square feet.
Which side of OSB goes down?
Using OSB Safely The side stamped “This Side Down” is typically the smooth side. This is mostly for roofers so that they lay the smooth side down and can stand on the rough side facing up. When installing in vertical applications such as wall sheathing, you’ll want to orient the smooth or stamped side facing out.
Can you put 2 layers of plywood on a roof?
The new plywood will have to be nailed to the rafters or roof trusses. That increase in weight should not be a problem with the single layer of asphalt shingles you will be installing, because it is normally safe to assume the roof structure is built to support the weight of two layers of asphalt shingle roofing.
Do I need plywood on my roof?
Aside from shingles and underlayment, plywood decking is one of the most important components in your roof. The plywood decking is integral in keeping your home free of unwanted water and mold. If the plywood has gotten wet, it can have a disastrous effect on the rest of your roof, especially the shingles.
Can you use CDX plywood on a roof?
Only use CDX plywood for the interior of a house, where water damage is far less likely. Do not use CDX for roofing, sheds, or other places that are exposed to moisture consistently. The sole exception to this is pressure treated CDX, which can survive for decades without even a protective coating.
Can I use screws for roof sheathing?
Screws can be used for even greater withdrawal strength, but should be sized by the building designer. Staples are not recommended for roof sheathing attachment in high-wind areas. It is extremely important to have proper fastener spacing on all panels.