- 1 What is tongue and groove plywood used for?
- 2 Do you have to use tongue and groove plywood for subfloor?
- 3 What is T&G plywood?
- 4 Is tongue and groove plywood waterproof?
- 5 Is it better to nail or screw subfloor?
- 6 Why do people have tongue and groove flooring?
- 7 How tight should tongue and groove be?
- 8 Is it better to use OSB or plywood for subfloor?
- 9 Why is plywood so expensive?
- 10 What is the thickest plywood?
- 11 Do they sell 1 inch thick plywood?
- 12 What is the thinnest tongue and groove plywood?
- 13 Can you cut tongue and groove in plywood?
What is tongue and groove plywood used for?
Tongue-and-groove plywood is superior to regular plywood for floor decks because it creates a stronger, more rigid subfloor, and helps eliminate sagging and “bounce” at the seams between the joists.
Do you have to use tongue and groove plywood for subfloor?
For subflooring, you use tongue and groove plywood. The tongue and groove are only along the 8 foot edges. On the four foot edges, your seams will fall on joist tops, so no need for tongue and groove.
What is T&G plywood?
Tongue and Grooved (T&G) plywood merges sub floor and underlayment into a single sturdy panel commonly used for use under carpet and pad, hardwood flooring, or vinyl tile; designed to be cut, drilled, glued, and nailed with ordinary tools.
Is tongue and groove plywood waterproof?
This plywood is for construction or other uses. The water-repellent coating protects against rain and moisture during construction. This product is span rated for 24″ on center and is guaranteed against delamination, edge swell and joint sanding.
Is it better to nail or screw subfloor?
Using code-approved screws rather than nails is the best option for avoiding movement. If using nails for subfloor installation, stick with ring-shank nails; smooth nails may withdraw easier, leading to squeaks.
Why do people have tongue and groove flooring?
Nearly all hardwood flooring today is tongue and groove because it solves the pesky problems—such as shrinking, warping, and working loose—commonly experienced by face-nailing planks to floor joists.
How tight should tongue and groove be?
All it takes is 1⁄8″. The joint should be a firm press fit: If you have to knock the pieces together, then struggle to pull them apart, the joint’s too tight. A tongue that’s a hair too fat for the groove may actually seat, but it will stress the groove sidewalls and may, in time, prompt them to split.
Is it better to use OSB or plywood for subfloor?
The National Tile Contractors Association and the Resilient Floor Covering Institute both recommend plywood for subflooring and underlayment, because it doesn’t have the risk of swollen edges that OSB does. Plywood also has a slight advantage in stiffness, which means that subflooring panels need not be quite as thick.
Why is plywood so expensive?
Wood products prices typically fluctuate more than most goods, because homebuilding can move up or down much faster than sawmill capacity can. Lumber and plywood prices are so high now because of the short-run dynamics of demand and supply. Wood demand shot up in the summer of pandemic.
What is the thickest plywood?
While 3/4” thick plywood is the thickest that is sold in sheets in most lumberyards and home improvement centers, plywood is commonly manufactured in 1” and 1 ¼” thick sizes as well. Some mills produce plywood up to 3” thick for special order.
Do they sell 1 inch thick plywood?
1-inch 4×8 Plywood, AC Fir Sanded, Full Thickness, Exterior Grade | Plywood Company Texas.
What is the thinnest tongue and groove plywood?
The thinnest plywood on the market ranges all the way down to 2mm thick (just over 1/16 inch). These are obviously specialty plywood products, manufactured for special applications which can’t be accomplished by any other product on the market, whether plywood or some other material.
Can you cut tongue and groove in plywood?
Since your groove in the plywood is centered, this bit setting will work for cutting both sides of the tongue in the edging. If it’s too thick for the groove, raise the router bit a little to cut a thinner tongue. If it’s too thin, lower the bit to make the tongue thicker.