- 1 Can you use plywood on a roof?
- 2 Should I nail or screw roof sheathing?
- 3 Should you stagger plywood on a roof?
- 4 What direction do you put plywood on a roof?
- 5 How much plywood do I need for a roof?
- 6 Is it better to nail or screw plywood?
- 7 What size nails do you use for roof sheathing?
- 8 Do you glue down roof sheathing?
- 9 Should I use OSB or plywood for roof?
- 10 Why do you stagger plywood?
- 11 Should plywood be installed vertically or horizontally?
- 12 Does it matter which way you lay plywood?
- 13 Do you hang plywood vertical or horizontal?
Can you use plywood on a roof?
Most roofs will be sheathed in plywood at least 3/8 inch thick. That will suffice on a roof with rafters set 16 inches apart with minimal roof loads. Loads will vary with the pitch of the roof; the flatter the roof, the greater the load on any one section. Steeper roofs will have lighter loads per square foot.
Should I nail or screw roof sheathing?
The cheapest and easiest is to re-nail or, better yet, screw down the sheathing when you replace your roof covering. The other approach is applying an AFG-01 rated adhesive to enable the roof sheathing to withstand pressure to 250 pounds per square foot or greater.
Should you stagger plywood on a roof?
Plywood panels should be laid with the face grain perpendicular to the rafter boards. The panels should be installed over two or more spans, with the long dimension or strength axis oriented across the rafter boards or truss cords. Staggering panels by at least two supports is recommended.
What direction do you put plywood on a roof?
A: According to APA—The Engineered Wood Association, wood panel sheathing should be oriented with their strength axis or face-grain direction perpendicular to the roof framing. This provides maximum stiffness and load capacity.
How much plywood do I need for a roof?
Divide the total roof area by 32 to get the number of sheets you will need to cover the roof. A typical 4 foot by 8 foot sheet of plywood covers 32 square feet. If your roof area is 1,600 square feet, 1,600 divided by 32 will mean you need about 50 sheets to cover the roof. Add 10 percent to allow for waste.
Is it better to nail or screw plywood?
To start with, most experts recommend screws over nails when working with plywood. Nevertheless, there are many projects built using nails with plywood. In most cases, the nails used are from a pneumatic finish nailer and are used in conjunction with wood glue.
What size nails do you use for roof sheathing?
Step 3: Fasten Roof Sheathing Panels Properly. Fasten panels with a minimum of 8d Common (0.131-inch by 2-1/2-inch) nails spaced a maximum of 6 inches on center at supported panel ends and edges. At intermediate supports, fasten panels 12 inches on center. In high-wind areas, more fasteners may be required.
Do you glue down roof sheathing?
Unlike flooring, DO NOT glue roof sheathing. Drive nails flush to the panel. Panel clips may also be required depending on the sheath- ing’s span rating and the actual framing spacing. Check local building codes for requirements.
Should I use OSB or plywood for roof?
OSB takes longer than plywood to get saturated, but also takes much longer to dry out. When used as roof sheathing, this tendency to hold moisture means it will degrade faster than plywood when exposed to chronic leaks.
Why do you stagger plywood?
The end joint is where one board or plywood sheet butts up against another. In almost every situation, it’s important to stagger these joints to avoid straight lines that extend in a perpendicular direction across the lengths of the boards. This is a matter of appearance, but more importantly, it’s one of stability.
Should plywood be installed vertically or horizontally?
On roofs and floors, sheathing is installed perpendicular to supports because this is the orientation that results in the strongest roof or floor. Wind loads perpendicular to a wall are similar to floor and roof loads, and installing sheathing horizontally makes walls better at resisting wind pressure.
Does it matter which way you lay plywood?
It is exceedingly important that the first whole line of plywood sheets be perfectly straight and square. Each subsequent piece of plywood will depend on the first piece being installed correctly. If you do this properly, you’ll have a beautiful plywood subfloor.
Do you hang plywood vertical or horizontal?
If the height of a wall is less than 8-feet, install the plywood (or OSB) vertically. If the height of a wall is greater then 8-feet, install the plywood (or OSB) horizontally.