- 1 How do you cut a subfloor against a wall?
- 2 How do you cut a plywood subfloor?
- 3 How do you cut plywood on a wall?
- 4 What saw cuts close to wall?
- 5 Can I use a jigsaw to cut subfloor?
- 6 How do you cut plywood without splintering?
- 7 What is the best tool to cut paneling?
- 8 How do I know if my subfloor is bad?
- 9 Should you lay plywood over plank subfloor?
- 10 Is it hard to replace subfloor?
How do you cut a subfloor against a wall?
Just use a circular saw as suggested, cut as close as possible to the wall. If you want to level it perfectly with the existing flooring you could use strips of 30# tar paper stapled to the joist or sheet rock shims if it needs lots of leveling. I have used both methods in my carpentry business with excellent success.
How do you cut a plywood subfloor?
Start at the end of one of a chalk line and cut the line with the saw. Repeat this and cut the remaining chalk lines on the subfloor. Make sure that each cut bypasses the intersection of an adjacent cut 1 inch to cut completely through the subfloor at the corners of the section. Remove the section of plywood.
How do you cut plywood on a wall?
Drill a hole in the inside top corner of the cutout using a 1/2-inch drill bit in a drill or driver. Insert the blade of a reciprocating saw into the hole. Turn it on and cut the the plywood along the lines that you drew for the cutout. When you come to within 2 inches of the floor, stop cutting.
What saw cuts close to wall?
What is a Toe-Kick Saw? A toe-kick saw is basically a circular saw with an extended arbor on which the blade is mounted. It is used to cut the tiles, luan, vinyl (or similar sub-floor materials) under the kick space close to the cabinet base. You can also use it to flush cut tiles closer to walls and cabinet base.
Can I use a jigsaw to cut subfloor?
For example, you will always be an inch or so shy of bathtubs, walls and bathtubs. In these cases, use a reciprocating saw, a jigsaw or an electric jamb saw normally used for doorjambs but flipped up on its side and used at an opposite angle to cut down into the floor.
How do you cut plywood without splintering?
How to Avoid Splintering and Tearing when Cutting Plywood
- Always use an appropriate blade for plywood, and be sure that it’s sharp.
- Be sure the good face of your plywood is closer to the outside of the blade.
- Then, add a strip of masking tape to both the top and bottom of the sheet, directly over the cut line.
What is the best tool to cut paneling?
Sabre Saw. For precision cutting and detail work, the best way to cut paneling is with a sabre saw with a fine tooth blade. It is fast and easy, but a sabre saw is extremely difficult to keep in a straight line when free-handing.
How do I know if my subfloor is bad?
9 Common Signs of Subfloor Damage
- Your floors are uneven or sunken in parts.
- Your floorboards squeak – loudly.
- The room smells musty.
- Your floors shift or bounce when you walk on them.
- Your toilet is rocking or loose.
- Your tile flooring has cracked.
- Your hardwood floor is cupping.
- Your linoleum floor is bubbling up.
Should you lay plywood over plank subfloor?
Take time to make sure your existing planks are well secured in place. Repair any broken planks. Install a layer of at least ½” or preferably 5/8” ply over the existing planks. Like all wooden flooring products, it’s a good idea to acclimatise your plywood before laying it.
Is it hard to replace subfloor?
The subfloor usually runs in a continuous sheet under all the walls. It can’t be removed easily. The underlayment, however, was put in after the walls were up, so it fits each room and is tailored to the type of floor covering being used. The underlayment, therefore, is easy to pull up and remove.