Often asked: What Plywood For Roof?

What kind of plywood do you use on roof?

CDX is the grade of plywood most commonly used for roofing (CDX plywood means it is Construction Grade for exterior purposes).

What thickness of plywood is used for roofs?

Most roofs will be sheathed in plywood at least 3/8 inch thick. That will suffice on a roof with rafters set 16 inches apart with minimal roof loads. Loads will vary with the pitch of the roof; the flatter the roof, the greater the load on any one section. Steeper roofs will have lighter loads per square foot.

What grade of plywood is used for roof sheathing?

1/2 or 3/4-inch Plywood for Roof Sheathing? – Traditionally, 1/2-in CDX plywood was common choice with 24-in rafter spacing. However, heavier roof loads may require the use of 3/4-in CDX plywood for roof sheathing. Roofs with less pitch often carry heavier loads, including snow and ice accumulations in the winter.

What is the best thickness for roof sheathing?

The recommended thickness for roof sheathing is ⅝” thick. Sheathing with a thickness of less than that is much more likely to result in bowing between framing which could potentially compromise your exterior roof material.

You might be interested:  Often asked: How To Route Birch Plywood Without Splintering?

Can you put plywood over plywood on roof?

The new plywood will have to be nailed to the rafters or roof trusses. But, with the old plywood left in place, it will be considerably more difficult to locate the rafters to ensure proper nail placement.

Should I use OSB or plywood for roof?

OSB takes longer than plywood to get saturated, but also takes much longer to dry out. When used as roof sheathing, this tendency to hold moisture means it will degrade faster than plywood when exposed to chronic leaks.

Do I need plywood on my roof?

Aside from shingles and underlayment, plywood decking is one of the most important components in your roof. The plywood decking is integral in keeping your home free of unwanted water and mold. If the plywood has gotten wet, it can have a disastrous effect on the rest of your roof, especially the shingles.

Is CDX plywood good for roofing?

Only use CDX plywood for the interior of a house, where water damage is far less likely. Do not use CDX for roofing, sheds, or other places that are exposed to moisture consistently. The sole exception to this is pressure treated CDX, which can survive for decades without even a protective coating.

How much is a sheet of plywood for roofing?

Your price could vary depending on how much the roofing company charges for labor, but generally, you can expect to spend between $70 to $100 for each sheet of plywood. A 4 x 8 sheet of plywood covers about 32 square feet of roof area—and the average roof measures about 3,000 square feet.

You might be interested:  Quick Answer: How To Remove Warp From Plywood?

What is the best plywood for a flat roof?

How to build a flat garage roof? A flat base is required to lay the roof covering on. This can be either Smartply OSB3 or good quality, structurally sound WBP plywood. A minimum thickness of 18mm must always be used.

Is 7/16 OSB OK for roofing?

or a non-laminated panel, such as this OSB. Either one is acceptable. The typical thickness of roof sheathing is about 7/16-inch, which is just under 1/2-inch. If you find 3/8-inch plywood installed as roof sheathing, it’s a good idea to make your client aware of its presence.

How long does roof plywood last?

There are a few averages you can expect, but they are dependent on these factors. Plywood siding, such as T-111 should give at least a 35 year life expectancy, if finished properly; but there are many cases of it lasting over 50 years. Roof sheathing should last 30 to 40 years or to put it another way, two roofs.

Leave a Reply

Your email address will not be published. Required fields are marked *