How Thick Is Roofing Plywood?

Is 7/16 OSB OK for roofing?

or a non-laminated panel, such as this OSB. Either one is acceptable. The typical thickness of roof sheathing is about 7/16-inch, which is just under 1/2-inch. If you find 3/8-inch plywood installed as roof sheathing, it’s a good idea to make your client aware of its presence.

What thickness of OSB is used on a roof?

What is the Standard Roof Sheathing Thickness? Standard roof sheathing thickness is ½” to ⅝” thick. If you are using OSB for your roof deck, then ⅝” is the recommended thickness. For plywood, which is slightly stronger than strand board, ½” thick is appropriate.

Which plywood is best for roofing?

CDX is the grade of plywood most commonly used for roofing (CDX plywood means it is Construction Grade for exterior purposes).

How thick should my roof sheathing be?

Asphalt shingle application directly over dimensional lumber is not permitted. For new construction, the roof decking shall be minimum 11 mm (7/16”) thick O.S.B. or minimum 12.7 mm (1/2”) thick plywood sheathing. When reroofing, plywood or O.S.B. roof sheathing shall be minimum 10 mm (3/8”) thick.

You might be interested:  Readers ask: What Plywood Is Used For Roofing?

Should I use OSB or plywood for roof?

OSB takes longer than plywood to get saturated, but also takes much longer to dry out. When used as roof sheathing, this tendency to hold moisture means it will degrade faster than plywood when exposed to chronic leaks.

Is OSB better than plywood?

Wood fiber is used more efficiently in osb. Osb is stronger than plywood in shear. Shear values, through its thickness, are about 2 times greater than plywood. This is one of the reasons osb is used for webs of wooden I-joists.

Do I need plywood on my roof?

Aside from shingles and underlayment, plywood decking is one of the most important components in your roof. The plywood decking is integral in keeping your home free of unwanted water and mold. If the plywood has gotten wet, it can have a disastrous effect on the rest of your roof, especially the shingles.

Can you put 2 layers of plywood on a roof?

The new plywood will have to be nailed to the rafters or roof trusses. That increase in weight should not be a problem with the single layer of asphalt shingles you will be installing, because it is normally safe to assume the roof structure is built to support the weight of two layers of asphalt shingle roofing.

Can I use screws for roof sheathing?

Screws can be used for even greater withdrawal strength, but should be sized by the building designer. Staples are not recommended for roof sheathing attachment in high-wind areas. It is extremely important to have proper fastener spacing on all panels.

You might be interested:  FAQ: What Is Rtd Plywood Used For?

What is the best plywood for a flat roof?

How to build a flat garage roof? A flat base is required to lay the roof covering on. This can be either Smartply OSB3 or good quality, structurally sound WBP plywood. A minimum thickness of 18mm must always be used.

Is CDX plywood good for roofing?

Only use CDX plywood for the interior of a house, where water damage is far less likely. Do not use CDX for roofing, sheds, or other places that are exposed to moisture consistently. The sole exception to this is pressure treated CDX, which can survive for decades without even a protective coating.

How much does roofing plywood cost?

Your price could vary depending on how much the roofing company charges for labor, but generally, you can expect to spend between $70 to $100 for each sheet of plywood.

Are roof sheathing clips required?

For the most common roof sheathing in our area, which is 1/2” nominal (7/16” actual) sheathing over trusses or rafters at 24” on center, there is no requirement for H-clips. One or two H-clips will often allow a longer span between roof trusses/rafters.

How long does roof plywood last?

There are a few averages you can expect, but they are dependent on these factors. Plywood siding, such as T-111 should give at least a 35 year life expectancy, if finished properly; but there are many cases of it lasting over 50 years. Roof sheathing should last 30 to 40 years or to put it another way, two roofs.

Leave a Reply

Your email address will not be published. Required fields are marked *